| |
Topic Title |
Forum |
 |
The importance of the filament detection sensor calibration (MK3S) and other problems By Nico2126 20 hours ago | Last Post: 8 hours ago
|
Assembly and first prints troubleshooting |
|
 |
TPU Druck wird luftig,... By thk_ms 1 week ago | Last Post: 8 hours ago
|
Zusammenbau und Fehlersuche bei den ersten Druckversuchen |
|
 |
Soluble support print setting not showing in prusaslicer By shaunlewis38 19 hours ago | Last Post: 8 hours ago
|
Assembly and first prints troubleshooting |
|
 |
MK3.5 Bondtech Extruder & Mosquito By EvoDesigns 2 months ago | Last Post: 9 hours ago
|
General discussion, announcements and releases |
|
 |
WARNING Prusa is pulling a fast one on people who ordered their MMU3 last July By ChiTownGuy 3 days ago | Last Post: 10 hours ago
|
General discussion, announcements and releases |
|
|
|
Using a Prusa dual colour/extruder mod on a sovol sv06 By Matthew Desmond 10 hours ago | Last Post: 10 hours ago
|
General discussion & User Experience & Ideas |
|
 |
Purge tower won't stay stuck By TreeTolber 2 weeks ago | Last Post: 11 hours ago
|
How do I print this? (Printing help) |
|
 |
MK3.5 - usb webcam By sliverbaer 17 hours ago | Last Post: 11 hours ago
|
General discussion & User Experience & Ideas |
|
 |
Beagle camera V2 and MK4 By Julnar 7 months ago | Last Post: 12 hours ago
|
User mods - OctoPrint, enclosures, nozzles, ... |
|
 |
Speaker volume By 3DPrintM.D. 1 month ago | Last Post: 17 hours ago
|
Hardware, firmware and software help |
|
 |
[MK4, XL, MINI] Printer offline or unable to register By Tojik 7 months ago | Last Post: 18 hours ago
|
Bugs & Errors |
|
 |
Timelapse Videos By ShamusTheTinker 4 months ago | Last Post: 18 hours ago
|
General discussion, announcements and releases |
|
 |
Unable to Update to Firmware 6.0.0 By Garfon 19 hours ago | Last Post: 19 hours ago
|
Hardware, firmware and software help |
|
 |
ESP-32 PrintCam Set up on Prusa Connect By SmokeJaguar 2 days ago | Last Post: 19 hours ago
|
General discussion & User Experience & Ideas |
|
 |
PrusaSlicer shows G-code after slicing vase mode? By David Witkowski 3 days ago | Last Post: 19 hours ago
|
PrusaSlicer |
|
 |
How can I get my printer to work again. By tre4b 6 days ago | Last Post: 20 hours ago
|
How do I print this? (Printing help) |
|
 |
Problem mit dem Schrittmotor By nele22 1 day ago | Last Post: 20 hours ago
|
Allgemeine Diskussion, Ankündigungen und Veröffentlichungen |
|
 |
Non Planar for smooth print. By Frank_The_Rock 5 years ago | Last Post: 20 hours ago
|
Hardware, firmware and software help |
|
 |
6.0.0 Firmware for Original Prusa MK3.5 By Jan Kratochvíl 2 days ago | Last Post: 21 hours ago
|
General discussion, announcements and releases |
|
|
|
PI-camera not found where is the problem???? By avos46 1 day ago | Last Post: 21 hours ago
|
General discussion & User Experience & Ideas |
|