Recent Posts
 
Notifications
Clear all

Recent Posts
Forums  |  Topics  |     

Page 2 / 23
  Topic Title Forum
AlexLandherr I Have a Long Print Ongoing, Can I Pause It for the Night?   (1 viewing)

By AlexLandherr 1 month ago  |  Last Post: 3 hours ago

How do I print this? (Printing help)
 
NicholasNDB Help printing Monoprice PLA+  

By NicholasNDB 2 weeks ago  |  Last Post: 4 hours ago

How do I print this? (Printing help)
 
Will Colour Change (M600) Restart Position  

By Will 23 hours ago  |  Last Post: 4 hours ago

PrusaSlicer
 
Probuilder84 Extruder blob buildup has pulled out thermistor red wire and can't preheat head to clean blob  

By Probuilder84 16 hours ago  |  Last Post: 4 hours ago

General discussion, announcements and releases
 
max CAP for Erlenmeyer flasks  

By max 1 day ago  |  Last Post: 5 hours ago

How do I print this? (Printing help)
 
NicJak FINDA turns N/A the moment it should load filament  

By NicJak 1 month ago  |  Last Post: 6 hours ago

Hardware, firmware and software help
 
rokkzz MK3s (with MMU2) to MK3s plus upgraded parts confusion  

By rokkzz 6 hours ago  |  Last Post: 6 hours ago

Hardware, firmware and software help
 
Othila Looking for help with a repeated print issue  

By Othila 2 days ago  |  Last Post: 7 hours ago

How do I print this? (Printing help)
 
CR1Z Erste Schicht nach Zusammenbau  

By CR1Z 4 days ago  |  Last Post: 7 hours ago

Zusammenbau und Fehlersuche bei den ersten Druckversuchen
 
Andrea First layer problem  

By Andrea 10 hours ago  |  Last Post: 7 hours ago

General discussion, announcements and releases
 
Tgett Pinda knocking off supports, how do I print this?  

By Tgett 17 hours ago  |  Last Post: 7 hours ago

How do I print this? (Printing help)
 
SirWillibald Merkwürdiges Geräusch beim Drucken  

By SirWillibald 2 days ago  |  Last Post: 8 hours ago

Allgemeine Diskussion, Ankündigungen und Veröffentlichungen
 
Anthlon Mini+ Flashair?  

By Anthlon 1 day ago  |  Last Post: 9 hours ago

Hardware, firmware a software (Pomoc)
 
Liceo Printing a Box - Why only one edge is bad?  

By Liceo 5 months ago  |  Last Post: 10 hours ago

How do I print this? (Printing help)
 
Lubost Kvalita výtlačkov s prázdnym priestorom (napr. pre šrubku), pavučina na výtlačku  

By Lubost 15 hours ago  |  Last Post: 10 hours ago

Jak to vytisknu? (Pomoc s tiskem)
 
Abstract Mediums Is this a filament issue? Or the known issue with the heatbreak/plastic tube?  

By Abstract Mediums 2 days ago  |  Last Post: 12 hours ago

Hardware, firmware and software help
 
Marc Blobs of melted filament are fouling my print and causing crash errors  

By Marc 11 months ago  |  Last Post: 12 hours ago

General discussion, announcements and releases
 
pear3d.ch Prusa Bear Mini Mk3s  

By pear3d.ch 1 year ago  |  Last Post: 13 hours ago

User mods - OctoPrint, enclosures, nozzles, ...
 
Jrooker06 Feed to Nozzle  

By Jrooker06 4 months ago  |  Last Post: 15 hours ago

Hardware, firmware and software help
 
Page 2 / 23

 

 

 

Share: