|
Topic Title |
Forum |
|
Print head getting dropped in middle of print By TechnoSwiss 4 months ago | Last Post: 15 mins ago
|
General discussion, announcements and releases |
|
|
|
Help! Calibration failed. Check axes and run again. By proX gaming 3 hours ago | Last Post: 20 mins ago
|
Hardware, firmware and software help |
|
|
|
Select Objects to Print when in the queue By Mark Forster 18 hours ago | Last Post: 21 mins ago
|
General discussion & User Experience & Ideas |
|
|
|
"Nozzle Cleaning Failed." Error By Farlei 12 months ago | Last Post: 27 mins ago
|
Hardware, firmware and software help |
|
|
|
what would cause this ripply look in first layer? (1 viewing) By Dawson 3 months ago | Last Post: 35 mins ago
|
Hardware, firmware and software help |
|
|
|
We are hiring - Technical writer (1 viewing) By Jakub Dolezal 3 years ago | Last Post: 36 mins ago
|
General discussion, announcements and releases |
|
|
|
6.0.0 wifi firmware flashing failed By Tom Horsley 7 days ago | Last Post: 2 hours ago
|
General discussion, announcements and releases |
|
|
|
PI-camera not found where is the problem???? By avos46 1 week ago | Last Post: 3 hours ago
|
General discussion & User Experience & Ideas |
|
|
|
Multimaterial painted part has strange layer By cupajoe24 1 day ago | Last Post: 3 hours ago
|
PrusaSlicer |
|
|
|
Different hot blocks on the Mk4? By Samuel Miller 3 months ago | Last Post: 3 hours ago
|
User mods - OctoPrint, enclosures, nozzles, ... |
|
|
|
Should there be interface layers on the bottom layer of a support resting on a piece? By NoeG 14 hours ago | Last Post: 4 hours ago
|
General discussion, announcements and releases |
|
|
|
MMU3 & Prusa Slicer - how to prevent layer bleed into lower layers? Single blue layer is going six layers deep when slicing. By jurassic73 6 hours ago | Last Post: 5 hours ago
|
How do I print this? (Printing help) |
|
|
|
PrusaSlicer 2.7.4 can't install on Linux Mint By KyleM1990 5 hours ago | Last Post: 5 hours ago
|
PrusaSlicer |
|
|
|
Y Axis stuttering at same spot By Cailwen 14 hours ago | Last Post: 5 hours ago
|
Assembly and first prints troubleshooting |
|
|
|
Big problems with printing By gummiangler 14 hours ago | Last Post: 5 hours ago
|
Assembly and first prints troubleshooting |
|
|
|
Probleme bei Kalibrierung By gummiangler 3 days ago | Last Post: 5 hours ago
|
Zusammenbau und Fehlersuche bei den ersten Druckversuchen |
|
|
|
MMU3 printable parts R4 (F1) By Jakub Dolezal 2 weeks ago | Last Post: 5 hours ago
|
General discussion, announcements and releases |
|
|
|
Very Slow Bed Leveling By Rob Brown 4 days ago | Last Post: 6 hours ago
|
General discussion, announcements and releases |
|
|
|
Tuning bridging By ga 7 months ago | Last Post: 8 hours ago
|
PrusaSlicer |
|
|
|
So running a 2 day multi extruder job (factory assembled 5T) and getting filament changes on white PLA By Henryhbk 2 days ago | Last Post: 11 hours ago
|
Hardware, firmware and software help |
|
|