PursaSlicer 2.0.0 Not Responding
 
Notifications
Clear all

PursaSlicer 2.0.0 Not Responding  

Page 1 / 2
  RSS
SPARTAN_GIV
(@spartan_giv)
New Member
PursaSlicer 2.0.0 Not Responding

Hello,

I'm attempting to start the PursaSlicer 2.0.0  but it gets stuck at not responding.

Greatings

Publié : 05/08/2019 8:05 pm
SPARTAN_GIV
(@spartan_giv)
New Member
Topic starter answered:
RE: PursaSlicer 2.0.0 Not Responding

Oke here I have some update. The installer used is the 2.2.6 I could not download the 2.2.5 becouse it gave me a DNS error what I did attempt are the following things:

  • Reboot off PC
  • Reinstall
  • Run as admin
  • Install as admin

I'm using Windows 10 I did succeed in running inital setup

Is there annyone who knows how to fix this problem?

Publié : 05/08/2019 9:25 pm
Neophyl
(@neophyl)
Illustrious Member
RE: PursaSlicer 2.0.0 Not Responding

I installed the 2.2.6 on a new windows 10 computer last night and it installed and runs fine so its not a global issue.  I didnt install it admin either so I suspect its something about your pc it doesnt like.  I would open an issue on github for it and hope one of the devs can give you some debug instructions so they can figure out what the issue is. https://github.com/prusa3d/PrusaSlicer/issues

 

Publié : 06/08/2019 10:49 am
vintagepc
(@vintagepc)
Membre
RE: PursaSlicer 2.0.0 Not Responding

Maybe try moving/clearing the PS configuration directory? Could be something got junked up in there and is making it crash.

Publié : 06/08/2019 11:45 am
SPARTAN_GIV
(@spartan_giv)
New Member
Topic starter answered:
RE: PursaSlicer 2.0.0 Not Responding

Hey all thx for the replay I resolved the issue for now by removing leftovers in the %appdata% dir. I think something went rough

Publié : 06/08/2019 4:55 pm
SPARTAN_GIV
(@spartan_giv)
New Member
Topic starter answered:
RE: PursaSlicer 2.0.0 Not Responding

Hey all, Update. Again same problem. No cleu why

 

 

Publié : 11/08/2019 1:46 pm
Vojtěch Bubník
(@vojtech-bubnik)
Membre Admin
RE: PursaSlicer 2.0.0 Not Responding

Usually it is a graphics card driver issue or incompatibility with PrusaSlicer. Sometimes an update of the graphics card driver helps.

As a workaround, you may try the software renderer by copyling the opengl.dll from the MESA directory next to the PrusaSlicer.exe, though the software renderer will be quite slow.

 

Publié : 19/08/2019 9:29 am
Vous a aimé
captmark
(@captmark)
Active Member
RE: PursaSlicer 2.2.6 Not Responding

I am having the same issue what I have tried;

4x,. Uninstall, Reinstall, updated all drivers, uninstalled other slicer software, reinstalled PS 2.2.6. No help. Next is a HAMMER!

 

Publié : 25/08/2019 10:45 pm
--
 --
(@)
Illustrious Member
RE: PursaSlicer 2.0.0 Not Responding

 PS 2.2.6.   You mean the driver package?  P.Slicer is only at 2.0.0 released.  2.1.0-alpha (2.1.0-beta is seriously broken).

 

Publié : 26/08/2019 10:02 am
captmark
(@captmark)
Active Member
RE: PursaSlicer 2.0.0 Not Responding

Thank you for the response. Yes the driver package. I have a new dell i7 gaming laptop with nvidia 1060 card and 16gb of ram. All drivers are up to date.

Publié : 26/08/2019 10:56 am
--
 --
(@)
Illustrious Member
RE: PursaSlicer 2.0.0 Not Responding

For grins, go into the slicer folder, copy the exe and rename the copy to remove the dash.

C:\Program Files\Prusa3D\PrusaSlicer\prusa-slicer.exe

to

C:\Program Files\Prusa3D\PrusaSlicer\prusaslicer.exe

Then try running the renamed copy.

 

ps: Also - if you don't have a printer profile select (or installed) - that can give you grief.

Ce message a été modifié il y a 5 years par --
Publié : 26/08/2019 11:29 am
--
 --
(@)
Illustrious Member
RE: PursaSlicer 2.0.0 Not Responding

And have you tried deleting the Prusa specific appdata folder - then reinstall ??

C:\Users\<whoever>\AppData\Roaming\PrusaSlicer

Publié : 26/08/2019 11:35 am
captmark
(@captmark)
Active Member
RE: PursaSlicer 2.0.0 Not Responding

Hi, I did try taking the dash out, no help. I also deleted the app folder as well, no help. Thanks for the reply.

Publié : 26/08/2019 4:04 pm
captmark
(@captmark)
Active Member
RE: PursaSlicer 2.0.0 Not Responding

@tim-m30 I got it resolved. Seems it was a compilation of possible things that was causing it to lock up.
This was the sequence that cleared it, uninstalled completely, updated all video drivers, deleted the appdata folder, rebooted 2x, reinstalled the Driver pack and PS 2.0. I suspect you were correct in your assumption of the Appdata folder, there must have been a corrupt file in there.

Thanks for the help,

Publié : 26/08/2019 9:06 pm
ty.b
 ty.b
(@ty-b)
Eminent Member
RE: PursaSlicer 2.0.0 Not Responding

I just went through pretty much the whole process.  What finished it for me, was removing ALL old files associated with PrusaSlicer from my %appdata% folder.

https://www.pcworld.com/article/2690709/whats-in-the-hidden-windows-appdata-folder-and-how-to-find-it-if-you-need-it.html

I did a full, 100% fresh re-install, and it immediately started up when I launched from the shortcut on the desktop.

Publié : 15/09/2019 8:03 pm
Snype
(@snype)
Eminent Member
RE: PursaSlicer 2.0.0 Not Responding

Yeah.. If it's what I think it is, I posted on it in a few Redit forums.

There is a bug in the way the program closes when it is closed on a secondary or tertiary monitor.  In the INI folder in C:\Users\[YOURNAME]\AppData\Roaming\PrusaSlicer contains a line that tells the slicer where it was on the monitor when it was closed last.  If it was closed on a non-primary monitor, it writes a value that it cannot use and freezes half way through loading.  

The line is:  window_mainframe = 465; 30; 1455; 1020; 0

If you delete this line or just delete the INI file, it will start working again without losing your presets; though you will have to click your way through the setup again if you delete the INI.

 

Hope this helps.

Mtn Mage

Publié : 17/09/2019 2:51 am
Daniel, CREATIVE CARSTEN, et 2 personnes ont aimé
ty.b
 ty.b
(@ty-b)
Eminent Member
RE: PursaSlicer 2.0.0 Not Responding

@mtnmage

You ever find yourself in the Baltimore/DC area, I'll buy you a drink.  Strong work!

Publié : 17/09/2019 3:14 am
Vojtěch Bubník
(@vojtech-bubnik)
Membre Admin
RE: PursaSlicer 2.0.0 Not Responding

> There is a bug in the way the program closes when it is closed on a secondary or tertiary monitor. 

> ....

 

This issue sounds like https://forum.prusa3d.com/forum/prusaslicer/prusaslicer-no-longer-opens/

We tested that scenario, it shall work. I will ask our tester to re-test it.

You may want to check  https://github.com/prusa3d/PrusaSlicer/issues/2522

The "Nahimic" driver that some manufacturers bundle with their laptops or motherboards seem to cause that issue. I am afraid we cannot do anything about it.

Publié : 17/09/2019 2:54 pm
ty.b
 ty.b
(@ty-b)
Eminent Member
RE: PursaSlicer 2.0.0 Not Responding

@bubnikv

If you let me know where to find the specifics of that driver, I can check a couple of computers here to see if that jibes.

Publié : 17/09/2019 3:13 pm
Vojtěch Bubník
(@vojtech-bubnik)
Membre Admin
RE: PursaSlicer 2.0.0 Not Responding

Look at this comment

https://github.com/prusa3d/PrusaSlicer/issues/2522#issuecomment-507145018

Unfortunately I don't know more than that. I sent a complaint to the Nahimic company, but I did not receive any answer. You may try to do the same.

 

Publié : 17/09/2019 3:20 pm
Page 1 / 2
Partager :