Notifications
Clear all

Bondtech firmware compatibility prusa  

  RSS
Justin
(@justin-5)
Active Member
Bondtech firmware compatibility prusa

Hello recently purchased a bondtech Prusa i3 MK3S+/MK3S / MK2.5S Mosquito upgrade kit along with the mosquito hot end. and installed the 3.10.0 firmware(FW3100-Build4990) my issue is I like to run my prints through octo print and it is not updating the total runtime or filament used on the prusa under statistics. it has ran about 50 hours since the upgrade and it only shows 18 minutes of total runtime on my printer. probably due to the fact I ran a program from the sd card directly. Is there a way to update this so it will show total runtime and filament used correctly? I have already tried re installing the software and it has done nothing. End of the day it works fine without showing the statistics but it would be nice.

Posted : 19/09/2021 2:14 pm
cwbullet
(@cwbullet)
Illustrious Member
issuer

I will check tomorrow but I do not think I have this problem.    

Posted by: @justin-5

Hello recently purchased a bondtech Prusa i3 MK3S+/MK3S / MK2.5S Mosquito upgrade kit along with the mosquito hot end. and installed the 3.10.0 firmware(FW3100-Build4990) my issue is I like to run my prints through octo print and it is not updating the total runtime or filament used on the prusa under statistics. it has ran about 50 hours since the upgrade and it only shows 18 minutes of total runtime on my printer. probably due to the fact I ran a program from the sd card directly. Is there a way to update this so it will show total runtime and filament used correctly? I have already tried re installing the software and it has done nothing. End of the day it works fine without showing the statistics but it would be nice.

 

--------------------
Chuck H
3D Printer Review Blog...
Posted : 19/09/2021 2:43 pm
Justin
(@justin-5)
Active Member
Topic starter answered:
thank you

that would be great!

Posted : 19/09/2021 6:44 pm
Justin
(@justin-5)
Active Member
Topic starter answered:
update

did you have  a chance to look into it?

Posted : 23/09/2021 12:17 am
cwbullet
(@cwbullet)
Illustrious Member
Confirm,

I do nothing I have this problem.  After this print, I will confirm.  

--------------------
Chuck H
3D Printer Review Blog...
Posted : 23/09/2021 12:21 am
cwbullet
(@cwbullet)
Illustrious Member
Stats

I mean, I do not think I have this problem.  The print just finished and my stats increased.  

Posted by: @cwbullet

I do nothing I have this problem.  After this print, I will confirm.  

 

--------------------
Chuck H
3D Printer Review Blog...
Posted : 23/09/2021 12:40 am
Justin
(@justin-5)
Active Member
Topic starter answered:
g code possibly

sorry for the late response. could you copy and past your start g code and end g code i want to make sure mine is similar.

Posted : 26/09/2021 12:05 am
cwbullet
(@cwbullet)
Illustrious Member
issue

Back reporting:  I recommend you report this issue to Bondtech.  I am having the same issues with HT Magnum firmware 3.10.  I thought I was not, but I was wrong.  After multiple prints, it is not updating the statistics.  

--------------------
Chuck H
3D Printer Review Blog...
Posted : 30/09/2021 11:03 am
cwbullet
(@cwbullet)
Illustrious Member
Update

Bondtech is looking into the issue.  

--------------------
Chuck H
3D Printer Review Blog...
Posted : 01/10/2021 1:01 am
Justin
(@justin-5)
Active Member
Topic starter answered:
tech support answer

ah ok and i have last reply i got was "Ok, so when printing from a USB drive do you still have that issue? To reiterate; statistics doesn't work when printing over USB SERIAL meaning pronterface or OctoPrint and we can't help you with that. This is a known issue in Prusa firmware. https://github.com/prusa3d/Prusa-Firmware/issues/196 6"

 

Posted : 01/10/2021 10:36 pm
cwbullet
(@cwbullet)
Illustrious Member
Hmm

This is hard to believe.  

--------------------
Chuck H
3D Printer Review Blog...
Posted : 02/10/2021 12:31 am
Justin
(@justin-5)
Active Member
Topic starter answered:
text title is stupid...

I can dm the name of the gentleman I was speaking with and logs of convo if you would like.

Posted : 02/10/2021 2:22 am
Share: