Notifications
Clear all

Octoprint Help needed. ORIGINAL PRUSA I3 MK3S  

  RSS
steven.s55
(@steven-s55)
New Member
Octoprint Help needed. ORIGINAL PRUSA I3 MK3S

Hi All

I just setup my new Mk3 and want to use octoprint with it. I tried to use the prusaprint from here https://www.prusa3d.com/download-prusaprint

But the image says its corrupted, i have downloaded it a few times and tried a few different ways to install it too my SD card (followed youtube tutorials) but have not go it to work.

So then i gave straight octoprint working ( i used it with my old anet A6) setup a profile for it but it was not right, im banged a bit. 

i see on the net there are a few conflicting profile settings around. 

 

Can someone post up the official profile settings for the Mk3s to use with octoprint, also whats going on with the prusaprint image?

 

Thanks

 

Steven

 

 

Posted : 13/07/2019 11:06 am
Dave
 Dave
(@dave-11)
Eminent Member
RE: Octoprint Help needed. ORIGINAL PRUSA I3 MK3S

Do you mean a profile for slicing via the Cura plugin in Octoprint? If so, can't help.

If you're just trying to use Octoprint as a general print server, not sure what you mean. I use an generic Octoprint setup I originally built for my Lulzbot, and it works fine. There's nothing specific to the printer in an Octoprint "profile" other than the print volume dimensions, which you can find in the manual that came with the printer, googling, on Prusa's site, etc.

Posted : 17/07/2019 4:20 pm
MG
 MG
(@mg)
New Member
RE: Octoprint Help needed. ORIGINAL PRUSA I3 MK3S

I found this information in the comments on this recommended video ()

Print bed & build volume Width (X): 250 Depth (Y): 210 Height (Z): 210 Check Custom bounding box X Coordinates Min: 0 Max: 250 Y Coordinates Min: -10 Max: 220 Z Coordinates Min: -1 Max: 210 Temperatures ABS Extruder: 255 Bed: 100 PLA Extruder: 210 [modified to 215] Bed: 60 We downloaded and printed the Raspberry PI case for B+/2 & 3 Vers. 2.1 from www.thingiverse.com/thing:2398913. We are running Ubuntu 16.04 and used the following commands: $: md5sum octopi-jessie-lite-0.14.0.zip $: unzip etcher-1.3.1-linux-x86_64.zip $: chmod a+x etcher-1.3.1-x86_64.AppImage $: sudo apt-get install libnss-mdns $: ssh [email protected] pi$: passwd pi$: sudo raspi-config Firefox: http://octopi.local

http://www.aiwerkstatt.com/3dprinter/octoprint/

Also,

Here are the Prusa I3 MK3 Octoprint settings from the video:

Name: Original Prusa I3 MK3 (or whatever you like)

identifier: (filled in automatically)

Model: Original Prusa I3 MK3

Click the Print Bed and Build Volume tab

Form factor: Rectangular

Origin: Lower Left

Heated Bed: yes X: 250, Y: 210, Z: 210

Custom Bounding Box: (not shown in the video) X: 0, 250 Y: -10, 220 Z: -1, 210

Click the Axes tab (not shown in the video; affects only manual control of the printer) X 6000 mm/min, Y 6000 mm/min INVERT, Z 200 mm/min, E 300 mm/min

Click the Hotend and Extruder tab (not shown in the video)

Nozzle Diameter: 0.4 mm

Number of extruders: 1

Posted : 09/08/2019 6:26 pm
Robert
(@robert-6)
New Member
RE: Octoprint Help needed. ORIGINAL PRUSA I3 MK3S

Those are for MK3 as written in the text and seen in the video. 

@martin-glass

Name: Original Prusa I3 MK3 (or whatever you like)

identifier: (filled in automatically)

Model: Original Prusa I3 MK3

For MK3S please take these settings:

Print bed & volume

Name: Original Prusa I3 MK3 (or whatever you like)

identifier: (filled in automatically)

Model: Original Prusa I3 MK3

Click the Print Bed and Build Volume tab

Form factor: Rectangular

Origin: Lower Left

Heated Bed: yes X: 250, Y: 210, Z: 210

Custom Bounding Box: not enabled!

Axes tab

X 10.200 mm/min

Y 10.200 mm/min

Z 720 mm/min,

E 7.200 mm/min

Hotend and Extruder

Nozzle Diameter: 0.4 mm

Number of extruders: 1

This post was modified 4 years ago by Robert
Posted : 18/11/2019 3:39 pm
rmm200
(@rmm200)
Noble Member
RE: Octoprint Help needed. ORIGINAL PRUSA I3 MK3S

Do your downloads from octoprint.org.

Prusaprint is really to support the Pi Zero W using GPIO. I don't recommend any part of that.

Pi 3B using USB is the trouble-free way.

Also: PrusaPrint is an image file. It gets written to your Pi micro SD. Use an image writer.

This post was modified 4 years ago by rmm200
Posted : 18/11/2019 5:44 pm
Mike Daneman
(@mike-daneman)
Estimable Member
RE: Octoprint Help needed. ORIGINAL PRUSA I3 MK3S

Definitely recommend downloading OctoPi from the Octoprint site and don't use the Prusa version.

 

https://octoprint.org/download/

Posted : 20/11/2019 11:12 pm
towlerg
(@towlerg)
Noble Member
RE: Octoprint Help needed. ORIGINAL PRUSA I3 MK3S

@mortalwombat

Noob question. Are you sure about the axes speeds, the only number I see in the spec is 200+ mm/s. I assume the /min was a typo.

Posted : 21/11/2019 3:31 pm
You liked
bobstro
(@bobstro)
Illustrious Member
RE: Octoprint Help needed. ORIGINAL PRUSA I3 MK3S
Posted by: @steven-s55

[...] Can someone post up the official profile settings for the Mk3s to use with octoprint, also whats going on with the prusaprint image?

There's a nice summary from Gina, the Octoprint developer, here which includes a link to the relevant Prusa configuration file from PrusaPrint which can be found here.

 

My notes and disclaimers on 3D printing

and miscellaneous other tech projects
He is intelligent, but not experienced. His pattern indicates two dimensional thinking. -- Spock in Star Trek: The Wrath of Khan

Posted : 21/11/2019 5:15 pm
bbrendon liked
luvology
(@luvology)
Active Member
RE: Octoprint Help needed. ORIGINAL PRUSA I3 MK3S

Thanks

Posted : 12/05/2020 4:09 am
nady2804
(@nady2804)
Active Member
RE: Octoprint Help needed. ORIGINAL PRUSA I3 MK3S

Another question regarding Octopi and Prusa MK3S

What's about the printbed profiles?

I have on my Prusa 2 different?

A smooth and the texture one printbed..

Must or how can i switch between the 2 printbeds because normal i would change it on Prusa display menu and of course they have different Z axis adjustments!

br

Manfred

 

Posted : 28/05/2020 12:00 pm
Rob
 Rob
(@rob-4)
Active Member
RE: Octoprint Help needed. ORIGINAL PRUSA I3 MK3S

@mortalwombat

hey, thanks for this, i am curious and extreemly noobtastic

10.200 is that 10200 or literally 10.200?

 

Posted : 11/07/2020 3:17 am
Robert
(@robert-6)
New Member
RE: Octoprint Help needed. ORIGINAL PRUSA I3 MK3S

@roblob

It’s 10200. It’s mm per minute. 

Posted : 11/07/2020 6:13 am
prusanewuser
(@prusanewuser)
Prominent Member
RE: Octoprint Help needed. ORIGINAL PRUSA I3 MK3S

Could anybody who has been using i3 MK3S with Octoprint please verify if the following values are correct?

Axes

X: 10200 mm/min

Y: 10200 mm/min

Z: 720 mm/min (10 times slower than E?)

E: 7200 mm/min

All Invert Control unchecked.

Posted : 11/07/2020 7:25 pm
Robert
(@robert-6)
New Member
RE: Octoprint Help needed. ORIGINAL PRUSA I3 MK3S

@peter-c20

Yes they are

Posted : 11/07/2020 7:54 pm
Rob
 Rob
(@rob-4)
Active Member
RE: Octoprint Help needed. ORIGINAL PRUSA I3 MK3S

@mortalwombat

thanks much! I appreciate the quick response. Octoprint is a blessing and a curse lol. 

 

Peace and Health!

Posted : 12/07/2020 5:50 am
Rob
 Rob
(@rob-4)
Active Member
RE: Octoprint Help needed. ORIGINAL PRUSA I3 MK3S

@mortalwombat

Question, 

 Octoprint constantly tells me the print is out of bounds, I have read that it is the first purge line. So i add the check box and do a -4 or so, is there a good standard to get rid of that warning other than disabling it?

Thank you.

Posted : 12/07/2020 5:52 am
Mike Daneman
(@mike-daneman)
Estimable Member
RE: Octoprint Help needed. ORIGINAL PRUSA I3 MK3S

@roblob

Check if you have "Enable Model Size detection..." checked under "Features".  If so, uncheck it.

There's also a feature under the profile definition to define a custom bounding box. I haven't used it, but you may try play with that to include the initial wipe region.

Posted : 12/07/2020 6:26 am
Dante
(@dante)
New Member
RE: Octoprint Help needed. ORIGINAL PRUSA I3 MK3S

I know this is a bit of an older note and wanted to share how to fix it by configuring the i3 MK3S correctly:

Following the instructions from https://help.prusa3d.com/en/article/octoprint-configuration-and-install_2182/

the key is to enable custom bounding box and change it to X: 0/250, Y: -4/210, Z: 0/210

Hope this helps

Posted : 10/01/2022 3:15 am
Share: