What is causing this strange artifact when printing PLA?
 
Notifications
Clear all

What is causing this strange artifact when printing PLA?  

  RSS
smooth_jamie
(@smooth_jamie)
Active Member
What is causing this strange artifact when printing PLA?

Hi All,

I wonder if anyone can help me before I need to buy any new parts. About a week ago my MK3S had a print failure where PLA accumulated in large quantities at the hot end, blocking the fan and damaging the thermistor and fan shroud. I bought a replacement from prusa3d, I replaced the thermistor sucessfully using this guide step by step ( https://help.prusa3d.com/en/guide/how-to-replace-thermistor-in-the-extruder-mk3s_131675 ) and finally printed a new shroud out of ABS and the printer prints again, but now I have a quality issue.

A strange print artifact appears in my PLA prints, and I am not sure what is causing it. I have attached pictures of what results I am expecting and what results I am getting i.e. a sample printed before the repair (figure 1) and a sample printed after the repair (figure 2). In figure 2 (the bad sample) the failure only occurs on one side of the cylinder. It starts as a gradient so isn't too noticable until it gets progresively closure towards the 'einsy side' of the printer, then it seems to have a sharp transistion back to normal.

Could this be bad cooling? It looks like ghosting caused by some 'tugging' on the umbilical, but the printer has no problem moving it's axis. Any ideas? Are there any tests I can perform to rule out certain causes?

 

Figure 1 - A good sample printed before the repair. The artifact doesn't exist and it is a perfect print.

Good sample

Figure 2 - A sample printed with the same print settings after the printer repair.

bad_sample

Figure 3 - Both samples compared together (left is good sample, right is bad sample).

good_and_bad_sample

 

 

Posted : 12/09/2021 9:45 am
cwbullet
(@cwbullet)
Illustrious Member
RE: Try slowing

Some this might be an artifact of print speed.  Slow the print speed and it might improve.  

Take a picture before you remove it from the print plate so we can see orientation.  

--------------------
Chuck H
3D Printer Review Blog...
Posted : 13/09/2021 9:49 am
smooth_jamie
(@smooth_jamie)
Active Member
Topic starter answered:
Hmmm

Hi cwbullet thanks for your reply. I am using default PrusaSlicer settings for Generic PLA so print speed should not be the issue (I will do some test prints at slower speeds though to see if this helps).

In fact I believe I've determined the problem, the ubilical from the einsy to the hotend carriage is sagging and rubbing on the heatbed cable. It only does this when the X-carriage is at the leftmost side of the printer (this explains why it only happens in one place in the print). I started the print again and kept it out the way with my hand while it printed and the quality issue went away, but of course it isn't a permenant solution!

I am going to print some cable chains to constrain the umbilical, to see if that helps.

Posted : 15/09/2021 9:17 am
JoanTabb
(@joantabb)
Moderator
Prusa Support Lol

Hi, when you replaced your thermistor, did you ensure that the NYLON Support filament was properly installed in the umbilical between the rear of the extruder, and the einsy box. 
this filament normally prevents your umbilical from sagging... 

It is usually fixed in mounting holes at both ends. one on the rear of the X carriage, and one on the Einsy case

regards Joan

I try to make safe suggestions,You should understand the context and ensure you are happy that they are safe before attempting to apply my suggestions, what you do, is YOUR responsibility. Location Halifax UK...
Posted : 15/09/2021 1:12 pm
smooth_jamie
(@smooth_jamie)
Active Member
Topic starter answered:
Doh!

Thanks for your reply JoanTabb!

I am assume it is sagging because it never rubbed on the other cable which feeds the heatbed before! Checking the Nylon support filament is a good spot, I had to undo some of the cable ties to insert the new thermistor so maybe I moved it by accident? I will check tonight.

Posted : 15/09/2021 3:32 pm
JoanTabb
(@joantabb)
Moderator

most likely issue is the Einsy end!, 

 

regards Joan

I try to make safe suggestions,You should understand the context and ensure you are happy that they are safe before attempting to apply my suggestions, what you do, is YOUR responsibility. Location Halifax UK...
Posted : 16/09/2021 9:37 am
smooth_jamie
(@smooth_jamie)
Active Member
Topic starter answered:
Yes it was!

Hi JoanTabb,

Looking inside the einsy case and inspecting the nylon filament didn't immediately offer up any obvious points of failure. However I removed it from the einsy side and re-seated everything so at least the cables don't rub anymore...

...and as if by magic the problem is now gone! Obviously I had dislodged the Nylon filament when installing the new sensor. Thanks for your help!

Posted : 16/09/2021 11:42 am
JoanTabb
(@joantabb)
Moderator

GOOD NEWS!

I try to make safe suggestions,You should understand the context and ensure you are happy that they are safe before attempting to apply my suggestions, what you do, is YOUR responsibility. Location Halifax UK...
Posted : 16/09/2021 1:47 pm
Share: