Notifications
Clear all

Heatbed thermistor E3D Einsy board connector  

  RSS
Traltixx
(@traltixx)
Active Member
Heatbed thermistor E3D Einsy board connector

My thermistor connector broke, I'm assuming I did it during setup. Will cutting the bad connector off and putting a new one on affect the readings? If replacing it wont cause a problem, does anyone happen to know the connector type?

Cheers,

Moe

Best Answer by cwbullet:

They are cheap/  I would just buy another.  Once you buy a crimper and parts, how much would you save?

Posted : 16/05/2021 6:41 pm
--
 --
(@)
Illustrious Member
RE: Heatbed thermistor E3D Einsy board connector

No - but make sure you have the correct pins and crimper, too.  You can usually remove the old pins from the shell by depressing the locking tabs of the old pins. You'll just need new pins. 

Posted : 16/05/2021 7:15 pm
Traltixx liked
Traltixx
(@traltixx)
Active Member
Topic starter answered:
RE: Heatbed thermistor E3D Einsy board connector

@tim-2

Thank you! I am double checking I have the right connector and a crimping tool for the pins

 

Posted : 16/05/2021 7:51 pm
--
 --
(@)
Illustrious Member
RE: Heatbed thermistor E3D Einsy board connector

Here's the BOM for the male header: just find the matching female parts.

J2, J3, J6, J7, J13, J14, J16 Digi-Key WM4800-ND Molex 0705430001 10 Pin Conn 7   CONN 2PIN VERT 0.1" SHRD LOCKING 70543-02 Connector 2pos 2 Positions Header, Shrouded Connector 0.100" (2.54mm) Through Hole Gold HDR2 -NA- -NA-
Posted : 16/05/2021 11:38 pm
Traltixx liked
cwbullet
(@cwbullet)
Illustrious Member
RE: Heatbed thermistor E3D Einsy board connector

They are cheap/  I would just buy another.  Once you buy a crimper and parts, how much would you save?

--------------------
Chuck H
3D Printer Review Blog...
Posted : 16/05/2021 11:41 pm
Laura F Farrell
(@laura-f-farrell)
Trusted Member
RE: Heatbed thermistor E3D Einsy board connector

In Europe a new thermistor costs under 10 euros, easier to buy one, but fixing it should solve the problem if you can.

Posted : 17/05/2021 1:35 am
Traltixx
(@traltixx)
Active Member
Topic starter answered:
RE: Heatbed thermistor E3D Einsy board connector

@laura-f-farrell

Thanks! I'm just setting mine up for the first time and found the connector had broken. I have some molex connectors and crimper already. I just wanted to make sure I had the correct parts.

Posted : 17/05/2021 1:54 am
Traltixx
(@traltixx)
Active Member
Topic starter answered:
RE: Heatbed thermistor E3D Einsy board connector

@cwbullet

I already have the crimper. I'm now going through my parts to see if I had the right terminal.

Posted : 17/05/2021 1:55 am
Traltixx
(@traltixx)
Active Member
Topic starter answered:
RE: Heatbed thermistor E3D Einsy board connector

@tim-2

Thanks! I'm checking my parts. I believe I already have the molex connector (variety pack from working on rPi projects).

Posted : 17/05/2021 1:57 am
Share: