English forum České fórum Polskie forum Forum Français Forum Italiano Foro Español Deutsches Forum Recent Posts Announcements Forums English forum Original Prusa i3 MK3 & MK3S & MK3S+ Assembly and first prints troubleshooting Notifications Clear all Assembly and first prints troubleshooting | RSS Page 2 / 213 Prev 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 209 210 211 212 213 Next Topic Title Last Post Views Posts Author Bad first layer print By Bob on Mar 14 769 3 Michael Oakle... Weird offset / missteps on Z axis or extrusion... By nio101 on Mar 10 729 9 nio101 Another XYZ calibration fail By troconn on Mar 09 3821 9 Asher Printing of prusa parts. By Bob on Mar 07 1126 2 Wazfoodle Z axis calibration Answered By Marek Jaros on Mar 06 1061 5 Marek Jaros X Shift on Recently upgraded mk3s+ By Robin on Mar 06 1152 3 Graeme Johans... The Base Showing Up On The External Layer By Robin on Mar 06 1100 2 LeeH Can't remove attached cable from motherboard..... By bobnosn on Mar 03 2246 10 PrusaVA Calibration failed, check axis and run again By Robin on Mar 01 987 2 Kraut55 Extruder destroyed the PIDA mount By Robin on Feb 28 1052 11 jlc1978 extruder stops turning mid print By tigertrainer on Feb 27 1090 7 tigertrainer Extruder parks at 0 when print is done. By Logan Elswick on Feb 24 971 3 Logan Elswick First Layer Major Change By Reed Bartlett on Feb 22 935 7 Reed Bartlett XYZ calibration, Bed calibration point was not... By Egor Sovtsov on Feb 22 20331 14 Kurosakidom Issue with Benchy By Thejiral on Feb 21 917 11 jdenver Upgrade order - Mk3S+MMU2S to MK3S+ or MK3S to... Answered By JoanTabb on Feb 19 1047 6 lp3dprint X Axis Belt and Tension Answered By Diem on Feb 18 2378 14 bambi Hotend not heating By karl-herbert on Feb 15 919 4 Kraut55 Request to check warped bed diagnosis and next... By Robin on Feb 14 889 4 jweob Radial Layer Shifts randomly in Z, two differe... By Joe on Feb 13 809 6 Joe Page 2 / 213 Prev 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 209 210 211 212 213 Next Share: