Avisos
Vaciar todo

Ikea Lack Enclosure - Sovol SV01  

  RSS
xenon2008
(@xenon2008)
Active Member
Ikea Lack Enclosure - Sovol SV01

Hello together!

I am new here and found that here many People has build an Enclosure for there Prusa Printers or other Printers.

I have a Sovol SV01, and asked me if somebody from here did already build such an Enclosure for this Sovol SV01 Printer?

Because one Ikea Lack is to low... And i also did not know if it will fit into the deepth?

Sorry for my Bad English i am not very Good in, because i am a German/Austrian User, with terrible English Skills.

 

Maybe somebody can help me?

 

Respondido : 13/01/2021 5:56 pm
bobstro
(@bobstro)
Illustrious Member
RE: Ikea Lack Enclosure - Sovol SV01

I think @towelrg has a Sovol, though I have no ide if he's using an enclosure. The bed dimensions of the Sovol SV01 are a bit smaller than the Prusa Mk3, so the measurements should be close. It looks like a 24x24inch (70x70cm) enclosure will suffice. Most enclosures made with the Lack tables are using 2-3 tables stacked with brackets holding them together.

My notes and disclaimers on 3D printing

and miscellaneous other tech projects
He is intelligent, but not experienced. His pattern indicates two dimensional thinking. -- Spock in Star Trek: The Wrath of Khan

Respondido : 13/01/2021 10:59 pm
xenon2008 me gusta
John Doe
(@john-doe-3)
Estimable Member
RE: Ikea Lack Enclosure - Sovol SV01

I got plexiglas 1m x 1m from hobby market, cut by hand to 44cm x 50 cm , so I had to raise the lack foot by 6 cm. There are some models already for it.

Like: Ikea Lack 90mm extension | PrusaPrinters

 

Respondido : 14/01/2021 6:53 am
xenon2008
(@xenon2008)
Active Member
Topic starter answered:
RE: Ikea Lack Enclosure - Sovol SV01
Posted by: @bobstro

I think @towelrg has a Sovol, though I have no ide if he's using an enclosure. The bed dimensions of the Sovol SV01 are a bit smaller than the Prusa Mk3, so the measurements should be close. It looks like a 24x24inch (70x70cm) enclosure will suffice. Most enclosures made with the Lack tables are using 2-3 tables stacked with brackets holding them together.

smaller? the Bed from the SV01 is 300x255mm

Respondido : 14/01/2021 2:13 pm
towlerg
(@towlerg)
Noble Member
RE: Ikea Lack Enclosure - Sovol SV01

Lack clearance height is approx 400mm, SV01 is approx 500mm. Footprint is about 500x540 (490x540 if LCD repositioned). Given that all the electronics are in the base, you probably want to get some airflow in there and seal off the underside of the base from the rest of the enclosure (draft excluder etc)

I don't have an enclosure, probably should.

Respondido : 14/01/2021 2:30 pm
PrusaPrinters profile
(@prusaprinters-profile)
Estimable Member
RE: Ikea Lack Enclosure - Sovol SV01

Servus kleiner Tipp:
https://forum.prusa3d.com/forum/deutsches-forum-allgemeine-diskussion-ankuendigungen-und-veroeffentlichungen/

Grüsse aus Wien.

Respondido : 15/01/2021 9:09 pm
Compartir: