Multimaterial Upgrade Test Prints
 
Notifications
Clear all

Multimaterial Upgrade Test Prints  

  RSS
PJR
 PJR
(@pjr)
Antient Member Moderator
Multimaterial Upgrade Test Prints

Needs to be cleaned up a little, but a nice print.

Peter

Please note: I do not have any affiliation with Prusa Research. Any advices given are offered in good faith. It is your responsibility to ensure that by following my advice you do not suffer or cause injury, damage…

Posted : 26/01/2017 4:13 pm
Marc
 Marc
(@marc-9)
Trusted Member
Re: Adalinda - 4 colour

How long did it take to print it in comparison to the one colour Adalinda?

Posted : 26/01/2017 4:24 pm
PJR
 PJR
(@pjr)
Antient Member Moderator
Topic starter answered:
Re: Adalinda - 4 colour

Cheshire Cat

Peter

Please note: I do not have any affiliation with Prusa Research. Any advices given are offered in good faith. It is your responsibility to ensure that by following my advice you do not suffer or cause injury, damage…

Posted : 26/01/2017 10:00 pm
patrick.s13
(@patrick-s13)
Eminent Member
Re: Adalinda - 4 colour

Those are awesome ! Thanks for sharing !

Posted : 15/02/2017 3:43 pm
herve.t
(@herve-t)
Active Member
Re: Adalinda - 4 colour

the cat is splendid! 😎

Posted : 15/02/2017 5:17 pm
john.c13
(@john-c13)
New Member
Re: Adalinda - 4 colour

Alice in the Wonderland! I love this kitty. Thanks for sharing, nice work!

Posted : 19/02/2017 11:15 pm
PJR
 PJR
(@pjr)
Antient Member Moderator
Topic starter answered:
Re: Adalinda - 4 colour

Here's a few articulated snakes:

Peter

Please note: I do not have any affiliation with Prusa Research. Any advices given are offered in good faith. It is your responsibility to ensure that by following my advice you do not suffer or cause injury, damage…

Posted : 20/02/2017 10:54 am
PJR
 PJR
(@pjr)
Antient Member Moderator
Topic starter answered:
Re: Multimaterial Upgrade Prints

6 x 3 colour Aria

Poor quality; I messed up, sliced with wrong settings (0.25 layer height, 0.5 width, way too fast). Needed to go out and forgot to change settings from previous slice - didn't realise until I returned.

Still, 11 hours 52 minutes, so not bad on time.

Peter

Please note: I do not have any affiliation with Prusa Research. Any advices given are offered in good faith. It is your responsibility to ensure that by following my advice you do not suffer or cause injury, damage…

Posted : 06/03/2017 9:06 am
3Delight
(@3delight)
Moderator Moderator
Re: Multimaterial Upgrade Test Prints

Looking good, can't wait for the kit to finally come out!

It's about time the Filament companies got their acts together when it comes to the quality (width and 'blobs') as it holds back development, costs everyone more money and work, and needs some sort of standards (one of those ISO xxxx or IEEEE xxxx ratings or something).

Posted : 11/03/2017 9:03 pm
PJR
 PJR
(@pjr)
Antient Member Moderator
Topic starter answered:
Re: Multimaterial Upgrade Test Prints

It's about time the Filament companies got their acts together when it comes to the quality (width and 'blobs') as it holds back development, costs everyone more money and work, and needs some sort of standards (one of those ISO xxxx or IEEEE xxxx ratings or something).

Yes, +1 on that. It happens with most filament providers though (including PR), but the 1.85mm limit on the current setup is too tight a tolerance.

Peter

Please note: I do not have any affiliation with Prusa Research. Any advices given are offered in good faith. It is your responsibility to ensure that by following my advice you do not suffer or cause injury, damage…

Posted : 14/03/2017 1:19 pm
Share: