Firmware Bug ( first time Wizard not working) Prusa Mini Self Test Problem
 
Notifications
Clear all

Firmware Bug ( first time Wizard not working) Prusa Mini Self Test Problem  

  RSS
Speedwood
(@speedwood)
New Member
Firmware Bug ( first time Wizard not working) Prusa Mini Self Test Problem

Hi @ all 

I have q big problem with my new mini :

Best Answer by padigree:

Pinned comment below the video:

"solution found sheet must be on it during the self test !"

 

But btw, the y axis sounds horrible.. Sounds like the sensorless homing would also not work properly.

Posted : 17/12/2019 10:52 pm
pingu
(@pingu)
Estimable Member
RE: Firmware Bug ( first time Wizard not working) Prusa Mini Self Test Problem

I habe the same problem

 

Posted : 18/12/2019 5:32 am
Oxygen
(@oxygen)
Reputable Member
RE: Firmware Bug ( first time Wizard not working) Prusa Mini Self Test Problem

What was the issue, since the topic of the video has (solved) in it...

Mini with FW:4.3.1 + SuperPINDA + Bondtech Heatbreak + PC4-M8 couplers + 1 piece boden...
Posted : 18/12/2019 7:29 am
padigree
(@padigree)
Trusted Member
RE: Firmware Bug ( first time Wizard not working) Prusa Mini Self Test Problem

Pinned comment below the video:

"solution found sheet must be on it during the self test !"

 

But btw, the y axis sounds horrible.. Sounds like the sensorless homing would also not work properly.

It’s better to give than to receive. Especially advice....
Posted : 18/12/2019 7:38 am
Oxygen
(@oxygen)
Reputable Member
RE: Firmware Bug ( first time Wizard not working) Prusa Mini Self Test Problem

Ah sorry, I looked at the video inline and did not see the comments -- thank you for the update

Mini with FW:4.3.1 + SuperPINDA + Bondtech Heatbreak + PC4-M8 couplers + 1 piece boden...
Posted : 18/12/2019 7:46 am
Speedwood
(@speedwood)
New Member
Topic starter answered:
RE: Firmware Bug ( first time Wizard not working) Prusa Mini Self Test Problem

Wizard bug on self test use the Sheet and the self check will be passed

Posted : 18/12/2019 11:16 am
Crawlerin
(@crawlerin)
Prominent Member
RE: Firmware Bug ( first time Wizard not working) Prusa Mini Self Test Problem

Maybe it would not hurt if it reminds about it on display, if it does not do tgat already. 

Posted : 18/12/2019 1:23 pm
towlerg
(@towlerg)
Noble Member
RE: Firmware Bug ( first time Wizard not working) Prusa Mini Self Test Problem

Kindda harsh to call this a bug.

Posted : 18/12/2019 2:14 pm
Crawlerin
(@crawlerin)
Prominent Member
RE: Firmware Bug ( first time Wizard not working) Prusa Mini Self Test Problem

@towlerg

No, it's not a bug, but can be frustrating nonetheless. If reminder of putting steel sheet to bed makes even just a few customers less frustrated, it may be worth putting it on screen or in manual.

Posted : 18/12/2019 2:28 pm
towlerg
(@towlerg)
Noble Member
RE: Firmware Bug ( first time Wizard not working) Prusa Mini Self Test Problem

@crawlerin

Point taken. It should be in the manual.

Posted : 18/12/2019 3:35 pm
towlerg
(@towlerg)
Noble Member
RE: Firmware Bug ( first time Wizard not working) Prusa Mini Self Test Problem

I had a look at the assemble instructions and Step 34 seems pretty clear. Also Step 35 shows the plate in place and notes "Place the PEI MINI sheet on the heatbed. Double-check it is oriented correctly."

This post was modified 2 years ago by towlerg
Posted : 18/12/2019 3:55 pm
Texy
 Texy
(@texy)
Reputable Member
RE: Firmware Bug ( first time Wizard not working) Prusa Mini Self Test Problem

That's fine when you are building and doing the very first calibration, but it needs to be clear, on-screen, from then onwards.

 

Posted : 18/12/2019 4:07 pm
Share: