English forum České fórum Polskie forum Forum Français Forum Italiano Foro Español Deutsches Forum Recent Posts Announcements Forums Members -- Activity -- Group: Registered Joined: 2018/09/10 Illustrious Member Yeah - alcohol is quite good at spreading fingerprints aroun...In forum General discussion, announcements and releases 5 months ago Most of these issues are due to simply not ensuring the set ...In forum Hardware, firmware and software help 5 months ago And piling on - the time taken for a few long 180 mm/s moves...In forum PrusaSlicer 5 months ago SPAM - as always - kick the poster and delete the thread ......In forum Awesome prints (Hall Of Fame) 5 months ago The ears are not really attached to the dog's head. I loaded...In forum How do I print this? (Printing help) 5 months ago Here's the startup gcode I use to make the layer one more co...In forum How do I print this? (Printing help) 5 months ago @merrill-a No - not if the measurement was done in circuit. ...In forum Hardware, firmware and software help 5 months ago Using a hot wire is a mistake. Just use a plain old cold cop...In forum Hardware, firmware and software help 5 months ago On large flat areas you can try this technique - when tweake...In forum Hardware, firmware and software help 5 months ago Welcome to the forums. Before anyone has a chance of helpin...In forum General discussion, announcements and releases 5 months ago One might ask why you are printing it on a raft? Supports a...In forum Hardware, firmware and software help 5 months ago Last place to check to verify the Rambo driver is probably s...In forum Hardware, firmware and software help 5 months ago Smaller coupons are less dependent on adhesion - larger coup...In forum General discussion, announcements and releases 5 months ago In Slicer, File Export Project as 3MF - save the file, creat...In forum How do I print this? (Printing help) 5 months ago Just looked it up: it's now recommended 3 Nm; 2.2 ft-lbs, 2...In forum Hardware, firmware and software help 5 months ago ps: You might examine the heat bed - look for any areas wher...In forum Hardware, firmware and software help 5 months ago And you have verified the 15a fuse is good?In forum Hardware, firmware and software help 5 months ago Problems in Z are pretty rare. A few ideas: When you built t...In forum Hardware, firmware and software help 5 months ago Post a photo of the nozzle in the heater block. There is no...In forum Hardware, firmware and software help 5 months ago @vlejundo I think you might have been logged in and not yet ...In forum General discussion, announcements and releases 5 months ago Page 2 / 321 Prev 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 217 218 219 220 221 222 223 224 225 226 227 228 229 230 231 232 233 234 235 236 237 238 239 240 241 242 243 244 245 246 247 248 249 250 251 252 253 254 255 256 257 258 259 260 261 262 263 264 265 266 267 268 269 270 271 272 273 274 275 276 277 278 279 280 281 282 283 284 285 286 287 288 289 290 291 292 293 294 295 296 297 298 299 300 301 302 303 304 305 306 307 308 309 310 311 312 313 314 315 316 317 318 319 320 321 Next Share:
