English forum České fórum Polskie forum Forum Français Forum Italiano Foro Español Deutsches Forum Recent Posts Announcements Forums Members cwbullet Activity cwbullet Group: Registered Joined: 2018/07/13 Illustrious Member @clarmrrsn I have agree they are worthless. I just can’t ev...In forum Coronavirus (COVID-19) 4 days ago Blastphomy. Who tires of orange?In forum General discussion, announcements and releases 4 days ago I will give this a try tonight. I have one that is a little...In forum User mods - OctoPrint, enclosures, nozzles, ... 4 days ago I read the article from Duke and the researchers in their an...In forum Coronavirus (COVID-19) 4 days ago @alexxriot It is virtual if not completely possible for a fa...In forum Coronavirus (COVID-19) 4 days ago If I see wavy lines, I pack off -0.020 until they go away.In forum How do I print this? (Printing help) 5 days ago @lize I will have to try that one.In forum How do I print this? (Printing help) 5 days ago Your Z could also be too negative.In forum How do I print this? (Printing help) 6 days ago I would definitely loosen the idler screw just a touch and t...In forum Assembly and first prints troubleshooting 6 days ago @lung I have ordered by mistake 2.85 mm parts a couple of ti...In forum User mods - OctoPrint, enclosures, nozzles, ... 6 days ago California filament has a special - 20% off if you order 3 r...In forum General discussion, announcements and releases 6 days ago Also, are you telling it to “change filament” under “Tune”? ...In forum Hardware, firmware and software help 6 days ago @doctorrudd Then Prusa's initial offering is not for you. T...In forum General discussion, announcements and releases 6 days ago @daryl-2 That works if you rough it up.In forum Hardware, firmware and software help 7 days ago @boatbuilder Good points. Thanks.In forum User mods - OctoPrint, enclosures, nozzles, ... 7 days ago @3djoe California filament is a quality vendor if you need P...In forum General discussion, announcements and releases 7 days ago woohoo! I thought this was a new or special edition model b...In forum General discussion, announcements and releases 7 days ago @eirlink That is hillarious. Enjoy your Haribos.In forum General discussion, announcements and releases 7 days ago @gregor-2 enjoy!In forum General discussion, announcements and releases 7 days ago Prusa XL. I prefer the support and tested software behind i...In forum General discussion, announcements and releases 1 week ago Page 2 / 314 Prev 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 217 218 219 220 221 222 223 224 225 226 227 228 229 230 231 232 233 234 235 236 237 238 239 240 241 242 243 244 245 246 247 248 249 250 251 252 253 254 255 256 257 258 259 260 261 262 263 264 265 266 267 268 269 270 271 272 273 274 275 276 277 278 279 280 281 282 283 284 285 286 287 288 289 290 291 292 293 294 295 296 297 298 299 300 301 302 303 304 305 306 307 308 309 310 311 312 313 314 Next Share:
